MEASUREMENTS TO BE MADE WITH BEAM
		              DRAFT 25 Sept. 1996
		              V. Burkert, D. Sober

     This schedule was discussed at the CalCom representatives meeting
     of Sept. 1996.  Some items to be clarified are indicated by Notes.

     					SYSTEMS ABBREVIATIONS:
					Ac = Accelerator
     LEFT COLUMN SYMBOLS:         	BL = Beam line devices         
     Tag = tagger magnet field on       CC = Cerenkov counters   
     Rad = tagger radiator in           DC = Drift chambers      
     Tor = CLAS torus field on          EC = Electron calorimeter
     Min = Mini-torus field on          Ta = Tagger              
     Tgt = CLAS target in               TOF = TOF counters       
     					Tr = Trigger + DAQ       
                  
     T R T M T
     a a o i g						Estimated	Systems 
     g d r n t						8-hour shifts  
    
     		1   Test Hall B interlocks			1	Ac
	          	
     + - + - -	2   Tune 2.4 GeV beam up to tagger dump		3	Ac,Ta,
									BL

		3   Measure background rates (from tagger dump)	1    	all
			in CLAS and tagger detectors                            

     - - + - -	4   Steer e beam to Faraday cup			1	Ac,BL	

		5   Optimize backgrounds vs beam steering	1	Ac,BL,
									all

		6   Tune lowest possible current		0.5	AC

	Note:  Maybe move #6 later in run?
	
     - - + + +	7   Mini-torus on
     			Thin C target in (L < 10^33 cm^-2 s^-1   
			=> 3 mg/cm2 12C at 100 nA)

		8   Optimize mini-torus current,			TOF,EC,
			observing drift chamber currents and		CC,DC
			TOF, EC, CC, Reg.I rates		1
      
		9   Determine DC gas gains for run		0.5	DC

	Note:  May want to reverse order of 8 and 9. 

		10  Electron triggers (Level 1):			TOF,TR,
            		TOF.EC.[CC]					EC,CC
  
         	11  Vary EC energy threshold to get clean 
    			trigger					0.5	EC	
                                                                
		12  Check events using CLAS Event Display (CED)	0.5	all

		13  Take data with EC.TOF, TOF.CC to check 		EC,CC
			CC, EC efficiencies 			0.5    

		14  On-line histograms for diagnostics:                    
			TO BE DEFINED by Working Groups                        

		15  Write data for off-line analysis:		4	all
			Various level 1 triggers (TO BE DEFINED)     
			Vary DC HV? (TO BE DEFINED)
			Other       (TO BE DEFINED)

		16  Test Level 2 trigger in one sector		1	TR

     - - - + +	17  CLAS Torus off, Mini torus on
			Take data with minimum ionizing trigger 
			in EC, TOF for calibration 		1	EC,TOF

     - - - - +	18  Torus off, Mini-torus off
			Very thin target (0.3mg/cm2, L=10^32/cm2sec)
			Test DC performance for alignment
			measurements with straight tracks	0.5  DC,EC,TOF

     + + - - -	19  Tagger magnet on, radiator in, 
			beam counter at Faraday cup:
			Write data to check tagger counter 
			timing, etc.  				2	Ta

								__________
                			Total			19 (= 6.3 days)


     CONTINGENCIES:

     The above list accounts for only 19 of the scheduled 21 shifts, and is
     (possibly) generous in the 3 shifts scheduled for initial beam tuning.
     If accelerator problems take up more time than scheduled, preventing
     completion of the program listed above, then we propose

     1) reducing the 4 shifts of writing data for off-line analysis to 3 or
     possibly 2 shifts

     2) dropping tasks from the end of the list.