#00  $1	 unixtimesec		unix time in seconds, about 23+/-2 min earlier than "iocha17:date" (not synced with run data)
#01  $2	 iocha17:date		timestamp in "DDMMMYY hh:mm:ss" format, about 23 +/- 2 min later than "unixtime" (IS synced with run data) USE THIS TIME
#02  $3	 HacAi_hpchan0		pol3he cell RTD, target upstream (beam source), deg C
#03  $4	 HacAi_hpchan1		pol3he cell RTD, target, deg C
#04  $5	 HacAi_hpchan2		pol3he cell RTD, target middle, deg C
#05  $6	 HacAi_hpchan3		pol3he cell RTD, target, deg C
#06  $7	 HacAi_hpchan4		pol3he cell RTD, target downstream (beam dump), deg C
#07  $8	 HacAi_hpchan5		pol3he cell RTD, pumping high, deg C
#08  $9	 HacAi_hpchan6		pol3he cell RTD, pumping low, deg C
#09 $10  HacAi_hpchan7		reference cell RTD, deg C
#10 $11	 HacAi_hpchan8		reference cell RTD, deg C
#11 $12	 HacAi_hpchan9		reference cell RTD, deg C
#12 $13	 HacAi_hpchan60		refcell pressure gauge, psig
#13 $14	 HacAi_hpchan61		refcell vacuum gauge, torr
#14 $15	 HacAi_hpchan62		cooling jets flow rate, liters per min
#15 $16	 Z6104_DISTGO		target half waveplate encoder position
#16 $17	 Z6104_TPM.STAT		target half waveplate stepper motor status
#17 $18	 SMART_PA		ladder real time encoder position
#18 $19	 SMART_POS		ladder real time position in words
#19 $20	 SMART_DA		ladder desired/set encoder position
#20 $21	 SMART_SS9		?ladder stepper motor status?
#21 $22	 SMART_SA10		?ladder?
#22 $23	 SMART_SA9		?ladder?
#23 $24	 CLASER_RDSTATE		laser 1 status (off=0,enabled=1,on=2)
#24 $25	 CLASER_RDCUR		laser 1 read current in Amps
#25 $26	 CLASER_RDTEMP		laser 1 read temperature in C
#26 $27	 CLASER2_RDSTATE	laser 2 status (off=0,enabled=1,on=2)
#27 $28	 CLASER2_RDCUR		laser 2 read current in Amps
#28 $29	 CLASER2_RDTEMP		laser 2 read temperature in C
#29 $30	 CLASER3_RDSTATE	laser 3 status (off=0,enabled=1,on=2)
#30 $31	 CLASER3_RDCUR		laser 3 read current in Amps
#31 $32	 CLASER3_RDTEMP		laser 3 read temperature in C
#32 $33	 CLASER4_RDSTATE	laser 4 status (off=0,enabled=1,on=2)
#33 $34	 CLASER4_RDCUR		laser 4 read current in Amps
#34 $35	 CLASER4_RDTEMP		laser 4 read temperature in C
#35 $36	 CLASER5_RDSTATE	laser 5 status (off=0,enabled=1,on=2)
#36 $37	 CLASER5_RDCUR		laser 5 read current in Amps
#37 $38	 CLASER5_RDTEMP		laser 5 read temperature in C
#38 $39	 CLASER6_RDSTATE	laser 6 status (off=0,enabled=1,on=2)
#39 $40	 CLASER6_RDCUR		laser 6 read current in Amps
#40 $41	 CLASER6_RDTEMP		laser 6 read temperature in C
#41 $42	 CLASER7_RDSTATE	laser 7 status (off=0,enabled=1,on=2)
#42 $43	 CLASER7_RDCUR		laser 7 read current in Amps
#43 $44	 CLASER7_RDTEMP		laser 7 read temperature in C
#44 $45	 HacOMEGA_SP1		oven temp setpoint, deg C
#45 $46	 HacOMEGA_RTD		oven temp read, deg C
#46 $47	 HacOMEGAtemp_RTD	?oven air flow?????
#47 $48	 psub_aa_pos		hall a attenuator setting
#48 $49	 psub_ac_pos		hall c attenuator setting
#49 $50	 SMRPOSA		hall a slit position
#50 $51	 SMRPOSC		hall c slit position
#51 $52	 R00LPMESA		hall a laser phase
#52 $53	 R00LPMESC		hall c laser phase